Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterMr-Glass Door Installation: The Greenacres Owner’s Guide
We install and service Mr-Glass door components in Greenacres on a regular basis, and in most cases we can complete the work in one visit. The typical installed price for a Mr-Glass door replacement part in Greenacres runs between $240 and $680 depending on the specific component and the condition of the surrounding frame. Homeowners usually call us when the door starts dragging across the floor, refusing to latch, or letting daylight show around the edges where it did not before.
Here is what you need to know before you spend a dime: Mr-Glass doors built for the South Florida market use heavier-gauge aluminum than what you will find on a door manufactured for a northern climate, which means the replacement parts must match that heavier profile. A generic part that “fits” in the track will bind within a season or two. We stock the correct Mr-Glass-compatible components for Greenacres homes and check the frame condition before we quote anything.
Which Mr-Glass Models This Applies To
Mr-Glass manufactures several sliding and patio door lines, and the parts compatibility comes down to the frame series stamped on the door edge or header. The most common models we service in Greenacres are the MG-2000 and MG-3000 sliding patio doors, plus the MG-French double-door swing assemblies. Each series uses different roller assemblies, strike plates, and weather stripping profiles, and crossing those parts between series is where most failed DIY attempts in Greenacres begin.
Here is the compatibility gotcha we see on the job site: the MG-2000 and MG-3000 sound like they should share hardware, but the rollers are not interchangeable. The MG-3000 uses a wider tandem roller with a stainless steel bearing that sits roughly 1/4 inch higher in the track. If you install an MG-2000 roller in an MG-3000 door, the panel will sit low, drag, and eventually gouge the bottom rail. You will know the frame series by looking at the silver sticker on the interior door jamb near the top corner, or by measuring the roller housing width with the door pulled back.
The short version: we carry OEM-spec Mr-Glass replacement hardware on the truck for the common series, and we always confirm the series number before we touch the panel. TruePane is an independent service provider, not affiliated with Mr-Glass, but we have been matching their hardware in Greenacres long enough to know which parts go with which frames.
Signs Your Mr-Glass Door Installation Is Failing
- Dragging or grinding when you open or close. The tandem rollers have worn flat or the stainless bearings have seized from Florida humidity and grit working into the track. The door gets heavier every month until something gets scored.
- The door lifts up before it will move. This is a roller that has dropped off its adjustment screw. Every time you lift the door to close it, you are twisting the panel and putting pressure on the glass frame corners that were never designed for it.
- Visible daylight at the top or side when the door is closed. The weather stripping has compressed permanently or the panel has sagged out of square. In Greenacres, where summer rain arrives sideways, this gap is also where water starts getting into the wall cavity.
- The latch no longer lines up with the strike plate. The door has settled or the rollers have worn unevenly, leaving the panel low to one side. Forcing the lock just speeds up the frame damage.
- Condensation or fog inside the glass sealed unit. The hermetic seal on the double-pane unit has failed, which on a Mr-Glass door in South Florida happens faster than anywhere else because of relentless humidity swings. This is not a hardware fix; it is a glass replacement.
Each of these problems is repairable, but every month of dragging and lifting is doing more damage to the parts you cannot see: the bottom rail, the track, and the frame corners.
Replacement Cost & What’s Included
The installed cost for Mr-Glass door hardware in Greenacres generally falls into three ranges, and we quote line items on paper before any work begins:
- Roller assembly replacement: $240-$380, depending on MG-2000 vs MG-3000 series and whether both panels need new rollers.
- Latch, strike plate, and handle set replacement: $180-$320, including re-alignment and lock function check.
- Weather stripping and track reconditioning: $150-$280, including cleaning the track bed and re-setting the panel to square.
- Sealed glass unit replacement: $420-$680, depending on size and glass type, including removal, re-glazing, and new setting blocks.
What is included in every quote: the correct Mr-Glass-compatible part, disposal of the old hardware, adjustment of the panel so it sits true and operates without force, and our workmanship guarantee under the Done Right Promise. We do not quote one price over the phone and deliver another bill after the work is done. If the job turns up something we did not see coming, we stop and put it in writing before moving forward.
DIY or Call Us?
There are things a homeowner in Greenacres can safely check before calling us. You can clean out the bottom track with a vacuum and a stiff brush to remove the sand and grit that piles up against the door threshold. You can inspect the visible weather stripping for flattening. You can note whether the problem happens every time or only after rain, which tells us something useful about the frame.
But when it comes to pulling the panel and swapping rollers, this is a job that goes wrong quickly. A filled Mr-Glass glass panel can weigh 80 to 150 pounds, and lifting it out of the track on your own is how back injuries and broken glass happen. The same goes for sealed unit replacement: the glass is under internal stress, and setting it without the right setting blocks and isolation tape will crack the new unit within months.
Dale Kessler grew up off Jog Road in Greenacres and has been setting frames and hanging doors in Palm Beach County for going on two decades. The work he is best known for is impact-rated installations that pass inspection the first time, not after a callback. We would rather you spend ten minutes on the phone with us before you spend a weekend wrestling a door panel out of its track. One visit, quoting the obvious now, and no surprises after. Call (754) 339-0784 if you want a second set of eyes before you touch anything.
FAQs
In Greenacres, expect five to eight years from the OEM rollers before the stainless bearings start grinding, and less if the door faces a pool deck or the intracoastal where salt and moisture are in the air. The tandem rollers on the MG-3000 hold up slightly longer than the MG-2000 singles because the load is spread across two wheels. We also stock quality aftermarket equivalents for homeowners who want to match OEM spec without the longer lead time. Call (754) 339-0784 and we can tell you from the series number which way to go before the first visit.
Sometimes yes, but usually no. Once a roller bearing has gone flat, re-packing it with grease only buys weeks, and by then the track has started to wear. The exceptions are adjustable hinges and loose handle sets, which can sometimes be tightened and re-aligned without new parts. We will tell you which one applies to your door, because a square deal means not selling a replacement where a repair holds.
Roller replacement on both panels usually takes about an hour and a half on site, including adjustment and testing. A sealed glass unit replacement runs about two hours including removal of the old panel and setting the new one. We carry the common Mr-Glass parts on the truck, so in the majority of Greenacres calls there is no second appointment left hanging: the job is done properly the first day.
We stock the common Mr-Glass rollers, latch assemblies, and weather stripping profiles for the MG-2000 and MG-3000 series on the truck, along with quality aftermarket equivalents for PGT, CGI, and CWS products. The odd specialty piece can take a few days if it is ordered from the manufacturer. Either way, you will know the lead time before we are done measuring, not after you have already signed for the work.
Call TruePane for Mr-Glass Door Work in Greenacres
If your Mr-Glass door is dragging, rattling, or showing daylight around the edges, the right move is a free estimate from someone who knows these frames in Greenacres, not a stranger who has never pulled a Mr-Glass panel. We have been at this since 2008 in this community, and the standard on every job is the one Dale keeps on the whiteboard: if the pane is not true, the job is not done.
Call (754) 339-0784. A live person answers, we measure the opening twice, we quote manufacturer lines side by side on paper, and we register both warranty layers in writing before the truck leaves your driveway. No voicemail trees, no forms, no fine print you only see after the bill. That is how TruePane works, and that is what you are paying for when you call us to stand behind a door in Greenacres.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Greenacres and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.