Mr-Glass Window Replacement Nationwide | TruePane Windows & Doors

Mr-Glass Window Replacement: The Greenacres Owner’s Guide

If you have a Mr-Glass window or sliding door with a failed part, we stock and install Mr-Glass-compatible replacements throughout Greenacres, and most jobs run between $240 and $680 installed depending on the part and the frame condition. We carry OEM Mr-Glass hardware on our service trucks, and if a specific latch, roller assembly, or balance has been discontinued, we match it with a quality aftermarket equivalent that fits the same milled opening without modification. Most homeowners discover the failure the way you probably did: a slider that suddenly drags, a window that drops when you let go, or a latch that no longer catches the strike plate. The good news is that these are known failure points, we see them weekly in Greenacres, and we fix them on the first visit more often than not.

Call (754) 339-0784

If your Mr-Glass product is beyond a parts replacement and you need an entire window replacement in Greenacres, we handle that too, with side-by-side manufacturer quotes on paper before any work begins.

Which Mr-Glass Models This Applies To

Mr-Glass built and supplied windows and sliding glass doors across South Florida for years, and the parts we replace most often fall into three groups. First: horizontal slider rollers and tandem wheel assemblies, which wear flat on the bottom track and make the panel feel like it weighs twice what it should. Second: sash balances and spiral balance tubes on single-hung and double-hung windows, where the internal spring loses tension or the nylon bearing cracks from heat cycling. Third: latch hardware and keepers, where the pot-metal cam or the strike plate has wallowed out after twenty years of daily locking and unlocking.

The fastest way to identify what you have is to look at the metal tag or etched stamp on the corner of the sash or the door edge rail. Mr-Glass units built before the mid-2000s most often used a 3/4-inch tandem roller with a stamped steel housing. Later units moved to a 7/8-inch nylon-bodied roller with a deeper track engagement. This matters because installing the narrower roller in a wide track lets the panel ride too low, scrape the sill, and destroy the new roller within a season. We see that exact mistake from handyman repairs in Greenacres, and it is the first thing we check when we show up.

For OEM versus aftermarket: if Mr-Glass still supplies the part and it is in our distributor network, we use the OEM part and register the manufacturer warranty layer in writing. If the part is discontinued, we use aftermarket equivalents from reputable suppliers that match the original milled dimensions, and we tell you exactly which supplier and part number went into your window before we leave the driveway.

TruePane Windows & Doors is an independent service provider, not affiliated with Mr-Glass. We quote manufacturer lines side by side on paper, and Mr-Glass hardware is one of the lines we keep in regular rotation because so many Greenacres homes were built with them. We also stock parts for PGT, CGI, and CWS window systems.

Signs Your Mr-Glass Window Replacement Is Failing

• The panel drags or stops sliding smoothly. Rollers have flat-spotted or the nylon wheel has cracked. Left alone, the steel axle cuts into the aluminum track and turns a $140 roller job into a $400 track repair.
• The window drops when you release it or slams shut. The spiral balance or block-and-tackle assembly has lost spring tension. This is not dangerous on most residential sashes, but it will bow the frame and crack the glass if ignored through a Greenacres summer.
• The latch does not catch the strike plate. The cam inside the latch has worn, or the strike plate screws have stripped out of the soft aluminum frame. This also means the window is not sealing, which is why you feel air moving around the edges.
• You hear a grinding or metal-on-metal sound when opening or closing. A bearing inside the roller assembly has let go. The sound is the axle spinning inside the housing, and it is machining the track every time you move the panel.
• The window or door is visibly tilted in the frame. One roller has collapsed entirely or a balance has snapped. The sash is now riding on its frame rails, and every open and close is scraping the aluminum. This is how you end up replacing the entire unit instead of the part.

Replacement Cost & What’s Included

In Greenacres, Mr-Glass window replacement hardware typically lands in these ranges installed:

• Slider door roller assembly (single panel): $180 to $290
• Slider door roller assembly (both panels, with track cleaning): $320 to $460
• Single-hung or double-hung sash balance (per sash): $160 to $280
• Latch and keeper replacement (including re-tapping stripped screw holes): $120 to $220
• Full window unit replacement (Mr-Glass to new manufacturer line): $550 to $1,400 per opening, depending on size, impact rating, and frame material

Every quote is a written line-item price: the part, the labor, and any track or frame work all listed separately so you can see exactly what you are paying for. You will not get a change order after we open the wall or the track. Both warranty layers get registered in writing before our truck leaves your driveway, and the workmanship is covered by our Done Right Promise. If it is not done right, we make it right. No paperwork, no arguing.

DIY or Call Us?

There are a couple of things you can safely check before calling. Look at the bottom track: if it is packed with sand and pet hair, hose it out and run a dry cloth through the groove. That alone sometimes restores a dragging slider long enough to plan the repair. You can also check whether the latch finger is contacting the strike plate squarely, because a loose door alignment can make a perfectly good latch look broken.

What you should not do is pull the panel and start pressing bearings out of a roller housing. Aluminum slider panels are heavier than they look, especially in the 96-inch sizes common on Greenacres pool lanai doors, and a dropped panel will take out a tile floor or a foot. If the part needs replacement, call us at (754) 339-0784. We will send a background-checked, uniformed technician who has done this exact job in your neighborhood before.

FAQs