CGI Door Installation Nationwide | TruePane Windows & Doors

CGI Door Installation: The Greenacres Owner’s Guide

CGI door installation in Greenacres typically runs $450-$1,200 for a full frame or hinge replacement, depending on the series and whether the panel needs re-hanging. We stock common CGI door components on the truck and can usually complete the work in one visit. The way most Greenacres homeowners discover a failing part is gradual: the door starts dragging on the threshold in August, or the latch stops catching cleanly, and by the time it gets bad enough to notice, the underlying component has already been wearing for a season or two. Florida humidity and daily thermal cycling are hard on door hardware, and CGI’s impact-rated construction means the tolerances are tighter than a standard door, so small misalignment shows up faster.

Call (754) 339-0784

Which CGI Models This Applies To

CGI manufactures a range of impact-rated door lines, and the installation specifics depend on which series you have. The most common we work on in Greenacres are the Trolley Line (hinged in-swing doors), Estate Collection (heavier raised-panel profiles), and the newer CGI Sentinel series. The quickest way to identify your door is the label on the hinge edge of the panel, which carries a CGI series code, the Miami-Dade NOA number, and the manufacturing year. That label matters because hinge spacing, threshold geometry, and weatherstripping profiles differ between series, and a part that fits an Estate door will not necessarily seat correctly on a Sentinel frame. For hardware like hinges and rollers, we can source OEM CGI components through our supplier network, and for non-structural items like sweep seals and latch assemblies, we carry quality aftermarket equivalents that meet the same spec. One compatibility gotcha worth knowing: CGI’s older Trolley Line doors use a 4-1/2-inch hinge template, while the Estate Collection moved to 5-inch hinges. Mismatched hinges will bind. We verify the label before ordering anything, because guessing at a CGI part number is how doors end up shimmed crooked and re-hung twice.

Signs Your CGI Door Installation Is Failing

• The door drags or scrapes the threshold in humid months. Wood and composite frames absorb moisture from the air, and when that happens, the reveal between panel and jamb closes up. In Greenacres, a door that was hung true in February can start binding by July if the original installer did not leave proper clearance.
• The latch bolt no longer slides into the strike plate without lifting or shoving. Hinges wear, screws back out of the jamb, and the panel settles by fractions of an inch. That small settlement is enough to throw the latch line off, and forcing the door makes the wear worse.
• You can see daylight or feel air moving around the weatherstripping. The seals on a CGI impact door are engineered to keep wind-driven rain and pressure out. When the seal collapses or tears, the door stops doing the job it was built for, and the air leak adds load to your HVAC.
• The frame shows hairline cracks at the hinge-side corners. This is common on older Greenacres homes where the slab has settled and the original frame was installed without full shim contact. Once the frame cracks, the structural integrity of the opening is compromised, and the door will never close square again until the frame is re-anchored.
• The door swings shut on its own or hangs open by itself. That is an out-of-plumb frame or failing hinges, not an adjustment issue. A properly installed door should hold its position anywhere in the swing arc. If yours drifts, the rough opening was never squared, or the hinges have been carrying weight they were not shimmed to bear.

Replacement Cost & What’s Included

For a Greenacres homeowner, figure $450-$1,200 for most CGI door installation work, depending on whether we are replacing hinges and re-hanging the panel or rebuilding the frame and setting a new threshold. A simple hinge swap with re-alignment sits at the low end. A full frame rebuild or a panel re-hang with new weatherstripping and threshold falls toward the middle. If the door itself is beyond saving and a new CGI panel has to be ordered, that number changes based on the series and size, and we quote it on paper before any work starts. Every quote we write in Greenacres is a line-item breakdown: parts, labor, and disposal separated out so you see exactly what you are paying for. The labor is covered by our Done Right Promise, and we register the CGI warranty layers in writing before our truck leaves your driveway. No surprise line items, no second appointment left hanging.

DIY or Call Us?

For a trained installer, changing out hinges on a 200-pound CGI impact door is a two-hour job. For a homeowner working alone with a floor jack and a pry bar, it is a pinched finger or a broken toe waiting to happen, and a door that lands wrong can damage the frame beyond a simple repair. What you can safely check: whether hinge screws have backed out, whether the threshold screws are still tight, and whether the weatherstripping is torn. Those are inspection points, not repairs. The honest truth is that a CGI door weighs more than a standard door, and working on one without a second set of hands and the right blocking is how a small fix becomes a frame replacement. If you are in Greenacres and the door is dragging, call us at (754) 339-0784 before you force it. A quick phone call costs nothing, and we will tell you straight whether it is a ten-minute adjustment or a real repair.

FAQs