CGI Impact Garage Doors Nationwide | TruePane Windows & Doors

CGI Impact Garage Doors: The Greenacres Owner’s Guide

CGI impact garage doors in Greenacres typically run $2,800 to $6,400 installed, depending on door width, reinforcement type, and whether the track and hardware need replacing at the same time. We stock replacement sections, bottom seals, roller assemblies, and hinge kits for most CGI residential series, and in many cases we can have the correct part matched and installed within 48 hours. Most Greenacres homeowners discover a problem the hard way: the door starts binding on one side in the afternoon heat, the bottom seal tears loose during a heavy summer downpour, or a post-storm inspection reveals a cracked panel that can no longer hold its Miami-Dade NOA rating.

Call (754) 339-0784

Which CGI Models This Applies To

CGI builds impact garage doors under two main residential lines: the Estate collection (wood-grain embossed steel, heavier gauge, typically 2″ thick sections) and the Sentinel line (flush or raised panel steel, 1-3/4″ sections, more common in Greenacres subdivisions built in the 1990s and 2000s). The gotcha that catches most owners is the older Econolight and pre-2005 CGI doors: those carried a different hinge spacing and narrower stile profile, so a new replacement section will not marry up cleanly unless you also swap the hinge row. When you call us, have the white manufacturer label on the inside of a panel ready. It has the series code and production date. If the label is missing, we measure the section thickness and the vertical stile spacing to figure out exactly what is on the track.

On the OEM versus aftermarket question for CGI specifically, we recommend OEM sections and OEM hinge hardware. Impact-rated doors carry wind-load ratings per panel, and mixing in an untested aftermarket section can invalidate the NOA listing on the whole door assembly. For seals, rollers, and struts, a good aftermarket equivalent from Clopay or Amarr holds up fine. But the panel itself, the part that takes the wind load, we source from CGI’s Florida distribution channel every time.

One more local note: CGI’s coastal-rated hardware and stainless hinge kits were a running change starting around 2008. A Greenacres door from before that era often has zinc-plated hinges that corrode at the pin within 10 to 12 years in our humidity. We replace those with the stainless version as a matter of course.

Signs Your CGI Impact Garage Door Is Failing

• The door starts binding or dragging on one side in the late afternoon. Florida heat expands the door sections and the track, and a door that was never re-lashed after settling will bind. We see this most often on west-facing garages in Greenacres, where the afternoon sun hits the door for six straight hours.
• A panel is dented, bulging, or shows a stress crack radiating from the hinge point. Once a section loses its flat profile, it no longer transfers wind load the way the NOA drawings assume. That single compromised panel can take the whole door out of impact compliance. This is the one we tell homeowners not to ignore.
• The bottom seal is torn, flattened, or missing in chunks. Greenacres gets 60-plus inches of rain a year. A failed bottom seal lets water in every storm, which rots the jamb, rusts the track brackets, and invites every ant colony in the neighborhood into the garage.
• The door is noticeably louder than it was two years ago and the sections shake going up. That is almost always worn rollers and loose hinge plates. On impact doors the extra section weight accelerates this wear. Swapping the rollers now is a couple hundred dollars. Ignoring it until a hinge tears out of a section is a full panel replacement.
• The door stops reversing properly or the cables are fraying. Frayed cables are a failure waiting to pop, and on an impact door the added section weight makes the cable under load far more dangerous than on a standard door. If you see any fraying, leave the door alone and call us.

Replacement Cost & What’s Included

For Greenacres, an installed CGI bottom seal replacement runs $140 to $220. Hinge and roller kits run $180 to $320 installed. A single replacement section runs $500 to $1,100 depending on series and finish, and a full door replacement runs $2,800 to $6,400 as noted. The spread depends on door width, sectional versus one-piece construction, and whether we need to re-square the existing track or replace it outright. We write a line-item quote on paper before any work starts, and the number on that paper is the number you pay. There is no change order drama. If a job runs into something unexpected, we stop and call you from the driveway, not from the end of a job with a surprise on the bill. Every CGI part we install is covered under our Done Right Promise: if it is not right, we make it right, no arguing and no fine print that covers neither.

DIY or Call Us?

Here is an honest split from a guy who has been setting frames and hanging doors in Palm Beach County for going on two decades. What you can safely check yourself: the bottom seal, the roller wear, whether the hinges feel loose, and whether the door sits square in the opening. You should not attempt to replace a torsion spring, re-tension the cable drums, or remove a section on your own. An impact-rated section weighs 40 to 60 pounds more than a standard panel, and the spring tension on these doors is serious enough to cost you fingers or worse. The few times we have arrived after a DIY attempt on a spring, the best-case scenario was a bent track; the worst-case scenarios are not something I care to repeat. If the door is not right in the opening, it will not be right in ten years. Call us at (754) 339-0784 and we will look at it. The visit and the quote are free.

FAQs